What Patio Covers Cost in Bakersfield, CA
Six calculators, one set of published rates, and a permit line that carries no figure because no current Bakersfield fee schedule could be verified. Everything the numbers are built from is on this page.
Patio and slabEvery planning range on this site
The calculators use exactly these bands. If a calculator ever produced a structure cost outside its band, that would be a bug rather than a market condition.
| Structure | Installed range | Unit | Typical |
|---|---|---|---|
| Concrete patio | $12 - $24 | per sq ft | $17 |
| Sunshades and solar screens | $12 - $28 | per sq ft of opening | $19 |
| Lattice patio cover | $22 - $40 | per sq ft | $30 |
| Alumawood patio cover | $28 - $48 | per sq ft | $38 |
| Solid patio cover | $30 - $52 | per sq ft | $40 |
| Deck | $35 - $75 | per sq ft | $52 |
| Insulated patio cover | $38 - $68 | per sq ft | $52 |
| Patio enclosure or sunroom | $65 - $130 | per sq ft | $95 |
| Louvered or motorised pergola | $75 - $150 | per sq ft | $110 |
| Outdoor kitchen | $200 - $700 | per linear ft of counter run | $430 |
Planning ranges for the Bakersfield market, not quotes. They cover the structure as installed and exclude the permit, which is set by the authority having jurisdiction and is not published as a fixed figure here.
Price your own project
Patio Cover
Set the size and compare the four roof types side by side. Above 3,500 feet Kern County adds a ground snow load, which is shown as its own line rather than buried in the rate.
$22 to $68 per sq ft →02Alumawood
Span is the driver on an aluminium system, not the colour. Removing a post is the single most expensive decision on this page.
$28 to $48 per sq ft →03Louvered Pergola
You are buying a mechanism. The frame is the cheap part, so the options that move this number are the drive and the seal.
$75 to $150 per sq ft →04Patio Enclosure
Screened, single glazed or dual glazed, and then the decision that changes the job: whether you condition it. Conditioning makes it an addition under the energy code.
$65 to $130 per sq ft →05Concrete Patio
Bakersfield largely sits on low-expansion sandy loam, which makes the slab easier here than in most of the Central Valley. Finish is what moves the price.
$12 to $24 per sq ft →06Deck
Material is the decision that matters, and in this valley it is a surface-temperature decision rather than a maintenance one.
$35 to $75 per sq ft →Why there is no dollar figure here
Most sites in this category publish a permit cost. This one does not, and the reason is specific rather than coy: the only Bakersfield fee schedule that could be found for this work was a proposed FY2021-22 document. A proposed schedule is not a current one.
Publishing it anyway would put a number on this page that somebody budgets against. So the permit appears in every calculator as its own line, with an em-dash where the figure would be, and the department that sets it named beside it.
City of Bakersfield
Community Development Department, Building Division
Applies inside the city limits, which includes areas such as Seven Oaks and Stockdale that read as suburbs but are city addresses.
Kern County
Kern County Public Works, Building Inspection Division
Applies to unincorporated areas, which includes Oildale and Rosedale despite their size, and every mountain and desert community on this site.
The rules behind the numbers
Span, the openness threshold and elevation move these figures more than the finish does. All three are on the permits page.
Costs and fees
What does a patio cover cost in Bakersfield?
Installed planning ranges run from about $22 per square foot for lattice to about $150 per square foot for a motorised louvered roof. Most Alumawood and solid work lands between $28 and $52. Those are the figures the calculators on this page use, and they are published rather than hidden behind a form.
Why is the permit not priced?
Because no current fee schedule for this work could be verified. The only Bakersfield document found was a proposed FY2021-22 schedule, and quoting a proposed figure as though it were current would be inventing a number. The permit is shown as its own line with no amount, and the department that sets it is named.
What is not included in these figures?
The permit, any engineering the department requires for your specific span, electrical work beyond the circuits listed as options, and site access difficulties. Distance from Bakersfield can also move the labour component for the mountain and desert communities.
Does elevation change the cost?
Yes, and the patio cover calculator prices it as a separate line. Under Kern County Code of Building Regulations 17.06.140 Kern County applies a 20 psf ground snow load from 3,500 to 4,000 feet and 30 psf from 4,000 to 5,000. Designing and framing for that is a real cost, so it is shown rather than folded into the rate.
Are these quotes?
No. They are planning ranges for the Bakersfield market, published so you can walk into a conversation with a number in your head. A quote comes from someone who has stood at the wall you want to attach to.